|
||
FAQs What is SoftDash?For a list of Softdash compatible devices click here or check your device for MIDP 2.0 with JSR-82 Support (Bluetooth wireless technology API)
What else do I need apart from the MFC?To use the window roll down/up feature you would need an additional window roll down module. The MFC talks to the window roll down module and tells it when to roll up/down the window. alarm system with a negative trigger would be necessary if the MFC is used to control an Alarm System with or without auto-start.Or just upgrade to the MFC V3 package that comes with a comple...
How can I get this device installed in my car?Installation of the MFC is straight forward if you know how to install car alarms/electronics. Any standard alarm/electronics installer can install the MFC system. The unit also comes with a complete step by step installation manual for both software (on the controller device) and hardware (in any vehicle). At the moment we also have affiliated installer locations for conv...
What is the range of Bluetooth wireless technology?The MFC 2 way communication tested in an outdoor parking lot produced 55ft of connectivity range and 150ft of communication range after connectivity. Connectivity is the initial process where the 2 devices (car and phone/PDA) search and initiate connection. Once connection is initiated, it received up to 150ft of communication on the class 2 device. This range will be smal...
Software Configurations.How do I configure it to my own car settings?In regards to the software setup. The MFC is the device installed into the vehicle. After the installer connects the MFC to the vehicle, the next step is to install the software configurations for those devices, e.g.output1=door lock action, output2= window roll down, e.g. a software button might control multiple outputs, e.g. with the case of engine start, you need about ...
Are there any software securities? Can someone hack my car system with another device?No, the wireless communication with the MFC over Bluetooth wireless technology is done over an authenticated and secure encrypted connection. I.e. first you need a password to connect to your car and then data sent over that connection is encrypted. Can be discovered and be connected to, where the connection will only be possible based on your connection settings. Can not ...
Can this be installed in any car?Yes. You can install this product in any car. Any alarm installer can install this product, and it also comes with a picture and page by page installation manual. Is it possible to have my system controlled by two different devices via Bluetooth wireless technology? E.g. my computer and Symbian phone. You can only control the system by one Bluetooth wireless technology dev...
Can I put a picture of my car in the software?Yes. You can customize your own skins in the software, change the sounds and rename or remap buttons e.g.
Can I read my tachometer with my Mobile phone, Palm Pilot or iPaq?Yes. You will be able to do that and also customize the effects that you want to happen when you hit your shift point and redline settings. You can also customize actions to happen when you hit a certain RPM, e.g. if I hit 5900 rpm, flash my neon underbody kits, or if I hit 6000 rpm, activate the NOS valve.
What kind of things I can control in my car with this product?You can only turn on and off the stereo with the MFC, to change controls such as volume, and change stations etc, you should get a nice universal remote control software that uses the infrared port on your handheld/device. Do a search for universal remote on www.pocketgear.com or www.palmgear.com. www.handago.com is another good place
Can I drive the car with my palm pilot/ Pocket PC Device?No, the vehicle does not have to be on to control the featured functions, if you have the MFC-V2 which is equipped with a Class 2 Bluetooth wireless technology antenna. There are aftermarket devices called shiftlights, whereby a driver sets a given RPM value where he intends to shift gear, when the engine revs up to the preset value, a light blinks, to indicate to the driv...
On the "Controls" screen, is there any way to customize the names of the buttons?To access the menu on a pocket PC device, hit the center key. There are drop down menu's on the main screen and the controls screen. All the buttons are customizable. By going into Menu> Options> Control Switch Settings. In the first drop down menu bar, select desired button. eg. Accessory 1. In Accessory 1- Here you can edit the name and color to be displayed on the... |
|
CONNECT2CAR: 3RD GENERATION CAR CONTROL SYSTEMS